Jacketed Tank, 6000 gallon, rated 70 psi at 80 degree fahrenheit, with top entry mixer, motor 3hp, 575 volt, 54 output rpm approx., with two top cip spray balls, sanitary interior polish, interior dimensions: 7 ft. wide x 25 ft. 8 in. high, discharge: 3 in., top ports: two 3 in., one 2 in., insulated with stainless steel cladding, manway: 14 in. x 17 in., with top stainless steel guarding, overall height: 36 ft., shipping dimensions: 1 piece, tank at 8 ft. wide x 36 ft. long x 10 ft. high, 1 piece, railing at 7 ft. 9in. wide x 7 ft. 9 in. long x 4 ft. high (Subject to Confirmation) (ID:7984,Mandatory Loading Fee: $1000)
Jacketed Tank, 150 gallon, rated: 120 psi at 350 degree fahrenheit, vessel rated: 120 psi, full vacuum at 350 degree fahrenheit, crn no. d2280.6, interior dimensions: 27 in. diameter x 56 in. long, top inlet: 6 in. (11 in. flange), center discharge: 2 in. (6 in. flange), distance from discharge to floor: 17 in., reactor mounted onto saddles, requires motor (ID:7396,Mandatory Loading Fee: $100)
Lee Industries Jacketed Kettle, mod. 50D9MT, 50 gallon, National board number: 11914, MAWP jacket: 90 PSI at 332 Fahrenheit, MDWT jacket 20 Fahrenheit at 90 PSI, MAWP internal 15 PSI at 250 Fahrenheit, MDMT internal 20 Fahrenheit at 15 PSI, designed for vacuum service, can be converted to scrape agitation with sourcing of poly scrappers, interior dimensions: 30 in. diameter x 24 in. height, top inlet: 2 x 1.5 in., 1 x in. 1 x 2 in. 1 x 8 in. tri clamps, pump motor: 2 hp, 208 230/460 volts, 3450 rpm, counter current agitator motor: 1 hp, 208/360 volts, 1650 rpm, gearbox: 66.42 ratio with 25 rpm output, scrape agitator motor: 2 hp, 208/360 volts, 1660 rpm, gearbox: 64.08 ratio with 26 rpm output, with variable speed motor controllers, with Sihi vacuum pump, with one control panel for kettle controls and one control panel for jacket temperature control, with Mokonft.s Duratherm cirulating water temperature control system, power requirements: 208 volts, shipping information: 54 in. wide x 102 in. long x 90 in. high, (Subject to Confirmation)(ID:9478,Mandatory Loading Fee: $50)
Tank, 33 gallon, max pressure: 50 psi at 300 degree fahrenheit, national board no. 402, rated full vacuum, dimensions: 22 in. diameter x 24 in. straight side, dish bottom, center discharge: 1.5 in., top inlets: three 2 in., with four interior mixing baffles, with stainless steel grab handles, vessel mounted on casters, overall shipping dimensions: 48 in. x 48 in. x 60 in. high 500 lbs (ID:8391,Mandatory Loading Fee: $50)
Tank, 80 gallon interior dimensions: 36 in. diameter x 18 in. deep, center discharge with pneumatic butterfly valve: 2 in. tri clamp, cone bottom, open top with lid, top inlets: one 7 in., one 2 in., one 1.5 in., two sets of three fixed blades, two sets of four rotating blades, motor: 3 hp, 575 volt, 1750 rpm, reducer ratio: 25/1, final output rpm: 70 approx., with temperature probe, with two cip spray balls, tank is on three stainless steel legs with pads, overall height with mixer: 88 in., link to test video:, https://www.youtube.com/watch?v=jnJFEZahl_c(ID:6920,Mandatory Loading Fee: $100)
Jacketed Tank, 1500 gallon, high pressure jacket rated : 150 psi at 428 degree fahrenheit, national board no. 1022, interior dimensions: 44 in. diameter x 96 in. straight side, plus dish bottom, center discharge: 6 in. flanged, falk heavy duty top entry mixer, motor: 20 hp, 230/460 volt, 1740 rpm, final output rpm: 190 approx., tank weight: 9000 lbs approx., shipping information: 5 ft 1 in. wide x 15 ft. long x 6 ft. 5 in. high (Subject to Confirmation)(ID:7762,Mandatory Loading Fee: $250)
Tank, 200 gallon, Insulated, interior dimensions: 50in. diameter x 27in. straight side, inverted dome bottom to 4in. flanged discharge, open top with two hinged lids, top inlets: two 2in. tri clamp, side ports: two 3in. flanged, 2in. insulation, tank is on four stainless steel legs, (ID:6765,Mandatory Loading Fee: $75)
Jacketed Tank, 7.5 gallon , electrically heated multi zone jacket, rating: atmospheric pressure at 350 degree fahrenheit, stainless steel control panel, with digital temperature controllers, with temperature gauge, interior dimensions: 16 in. diameter x 16 in. deep, top inlets: 3 in., 2 in. tri clamp, plus stainless steel vent, closed top with lid: 8 in. diameter, slope bottom to end discharge: 1 in. tri clamp, with grab handle, with locking casters, overall height: 42 in., (ID:7360,Mandatory Loading Fee: $50)
Imprex Jacketed Tank, 8000 gallon, jacketed for heating or cooling, with interior coil and coil support, with top entry Lighnin mixer, triple propeller, motor for hazardous locations: 3 hp, 575 volt, 855 rpm, reducer ratio: 17.31/1, final output rpm: 50 approx., interior dimensions: 8 ft. 6 in. diameter x 17 ft. straight side, plus dish top & bottom, center discharge: 6 in., top ports: 6 in., 5 in., 4 in., two 3 in., bottom ports: 6 in., 3 in., 2 in., with mixing baffle, insulated, tank is on four carbon steel legs with pads, top lifting lugs, shipping dimensions: 10 ft. 4 in. wide x 26 ft. long x 10 ft. high, weight: 31,000 lbs approx., manufacturers drawings available, distance from discharge to floor : approximately 16 in., (USA 2013)(Subject to Confirmation)(ID:8416,Mandatory Loading Fee: $1500)
Tank, 800 gallon, dimensions: 60in. diameter x 66 in. straight side, open top, dish bottom, center discharge: 4 in. tri clamp, with mixing baffles, tank is on four carbon steel legs with pads, overall height: 99 in., (ID:6713,Mandatory Loading Fee: $100)
Groen Tilting Kettle, 5 gallon, mod. TDB/7 20, jacket pressure rating: 50 psi at 300 degree fahrenheit, national board no. 100399, (ID:8346,Mandatory Loading Fee: $50)
JC Pardo Tank (Reactor), 26 gallon, Double Motion Scrape Agitation, completely refurbished by solinox in 2020, over $90,000 in refurbishment cost, jacket rated: 40 psi at 287 degree fahrenheit, national board no. 124, with scrape agitation, csa ul listed motor: 5 hp, 575 volt, 19 output rpm approx., with counter current mixer, csa ul listed motor: 5 hp, 575 volt, 157 output rpm approx., electrically driven hydraulic tilt out agitator, csa ul listed motor: 1 hp, 575 volt 3400 rpm, center discharge with valve: 3in. bevel thread, controls for scrape agitator, mixer & tilt out agitator, with sight glass, mounted on a stainless steel platform with casters, with full control panel & drives, overall dimensions: 3 ft. wide x 7 ft. long x 8 ft. high (Subject to Confirmation)(ID:7632,Mandatory Loading Fee: $50)
Tank (Vessel), 5 gallon, mawp 5 psi at 150 degree fahrenheit, dimensions: 18 in. diameter x 8 in. straight side, dish top & bottom, center discharge: 1.5in. tri clamp, top inlets: two 3 in., one 1.5 in. tri clamp, 10in. clamp down lid, with lifting lugs, with stainless steel grab handle, vessel mounted on locking casters, (ID:7354,Mandatory Loading Fee: $50)
Jacketed Tank, 300 gallon, jacket pressure rating: 150 psi at 300 degree fahrenheit, stainless steel contact parts, insulated with exterior carbon steel cladding, interior dimensions: 42 in. diameter x 53 in. straight side, with lid, with bracket for clamp on mixer, top ports: five 2 in., end discharge: 2.5 in. bevel sanitary thread, overall height: 94 in., jacket has been pressure tested, shipping dimensions: 50 in. wide x 94 in. long x 64 in. high at2000 LBS (ID:7696,Mandatory Loading Fee: $50)
Ross/Olsa Reactor, 25 Liter, working capacity: 25 liters, serial no. e00377 100837, jacket mawp: 65.25 psi (full vacuum) at 316.4 degree fahrenheit, shell mawp: 32 (full vacuum) at 282.2 degree fahrenheit, variable speed anchor & mixer, with stainless steel control panel, (Subject to Confirmation)(ID:7654,Mandatory Loading Fee: $50)
Tank, 900 gallon, interior dimensions: 56.5 in. diameter x 82 in. straight side, slope bottom to end discharge: 1.5 in. tri clamp, top ports: two 1.5 in. tri clamp, top manway with lid: 20 in., side bolted manway cover: 47 in. x 63 in., with lifting lugs, mounted on four stainless steel legs, overall dimensions: 60 in. x 60 in. x 106 in. high, preivous use: food application, shipping information: 64 in. wide x 108 in. long x 66 in. high, 1500 LBS (ID:7986,Mandatory Loading Fee: $100)
Tank, 1000 gallon, 135 Cu.ft. Storage Hopper, Stainless Steel, interior dimensions: 72 in. x 72 in. x 24 in. straight side, plus 42 in. cone bottom, top port: two 4 in., discharge: 6 in. x 5in., side ports: 9 in. x 8 in., 12 in. x 12 in., 15 in. x 15 in., mounting lip: 80 in. x 80 in., with electric vibrator, power requirements: 575 volt, (ID:7927,Mandatory Loading Fee: $50)
Jacketed Tank, 60 gallon, interior dimensions: 25 in. diameter x 30 in. deep, plus cone bottom, center discharge: 1.5 in., open top with lid, with lightnin clamp on mixer, motor: 0.3 hp, with variable speed, with waukesha stainless steel rotary lobe pump, model 6, capacity: 2 gpm approx., inlet & outlet: 1 in. x 1 in. tri clamp, with control panel, mounted on a stainless steel frame (56 in. x 60 in.) with casters, (Subject to Confirmation) (ID:7519,Mandatory Loading Fee: $50)
Precision Stainless Jacketed Tank, 435 gallon, jacket pressure rating: 150 psi at 100 degree fahrenheit, interior dimensions: 37.5 in. wide 60.5 in. long x 44 in. deep, top manway with lid: 18 in., top inlets: two 3 in., one 2 in., one 1.5 in., end discharge: 2 in., tank is insulated, on casters, shipping dimensions: 48 in. wide x 88 in. long x 80 in. high at 1000 LBS (ID:8107,Mandatory Loading Fee: $50)
Tank , 350 gallon, mawp: 50 psi at 300 degree fahrenheit, rated full vacuum, national board no. 219, crn no. l8728.5, sanitary interior polish, interior dimensions: 44 in. diameter x 48 in. straight side, plus dish top & bottom, center discharge: 2 in. tri clamp with valve, top inlets: three 1.5 in., one 2 in., two 3 in., one 4 in. tri clamp, 18 in. manway, with clamp down lid & gasket, with bottom mount agitator:, motor: 1 hp, 575 volt, 3450 rpm, output rpm: 500 approx., with two top cip spray balls, with level gauge, with lifting lugs, tank is on four stainless steel legs with pads, overall height: 108 in., shipping information: 48 in. wide x 102 in. long x 60in. high at 2000LBS (Subject to Confirmation) (ID:7483,Mandatory Loading Fee: $100)
Jacketed Tank, 100 gallon, vinterior dimensions: 29 in. diameter x 40in. straight side, center discharge : 3 in. tri clamp, dish bottom, open top, carbon steel frame, legs & platform, (ID:7424,Mandatory Loading Fee: $50)
Tank (Reactor), 550 gallon, vessel mawp: 50 psi at 300 degree fahrenheit, vessel rated full vacuum, national board no. 215, crn no. l8654.5, sanitary interior polish, interior dimensions: 48 in. diameter x 64 in. straight side, plus dish top & bottom, center discharge: 2 in. tri clamp with valve, 18 in. manway, with clamp down lid & gasket, with level gauge, insulated, with two top cip spray balls, with temperature probe, tank is on four stainless steel legs with pads, overall height: 128 in., shipping information: 58 in. wide x 128 in. long x 60 in. high at 2000 LBS (Subject to Confirmation) (ID:7482,Mandatory Loading Fee: $100)
Tank, 10 gallon, dimensions: 14 in. diameter x 24 in. straight side, slope bottom to end discharge: 1 in. tri clamp, open top with lid, with bracket for clamp on mixer, with stainless steel grab handle, mounted on locking casters, overall height: 48 in., (ID:7352,Mandatory Loading Fee: $50)
Feldmeier Tank, 10 gallon, dimensions: 14 in. diameter x 24 in. straight side, slope bottom to end discharge: 1 in. tri clamp, open top with lid, with stainless steel grab handle, mounted on locking casters, overall height: 48 in., (ID:7353,Mandatory Loading Fee: $50)
Tank, 250 gallon, mawp: 50 psi at 300 degree fahrenheit, rated full vacuum, national board no. 177, crn no. l8127.5, sanitary interior polish, interior dimensions: 36 in. diameter x 45 in. straight side, plus dish top & bottom, center discharge: 3 in. tri clamp with valve, with bottom mount agitator, motor for hazardous locations: 0.75 hp, 575 volt, 3500 rpm, with stainless control box with variable freqency drive, clamp down lid with gasket, with level gauge, with temperature probe, with lifting lugs, insulated, tank is on four stainless steel legs, overall height: 102 in., shipping information: 48 in. wide x 104 in. long x 54 in. high at 1500 LBS(Subject to Confirmation)(ID:7481,Mandatory Loading Fee: $100)
Walker Tank, 20 gallon, interior dimensions: 18 in. diameter x 25 in. straight side, slope bottom to end discharge: 1 in., open top with lid, with bracket for clamp on mixer, with stainless steel grab handles, tank mounted on locking casters, overall height: 49 in., (ID:7349,Mandatory Loading Fee: $50)
Walker Tank, 20 gallon, interior dimensions: 18 in. diameter x 25 in. straight side, slope bottom to end discharge: 1 in., open top with lid, with bracket for clamp on mixer, with stainless steel grab handles, tank mounted on locking casters, overall height: 49 in., (ID:7351,Mandatory Loading Fee: $50)
Walker Tank, 20 gallon, interior dimensions: 18 in. diameter x 25 in. straight side, slope bottom to end discharge: 1 in., open top with lid, with bracket for clamp on mixer, with stainless steel grab handles, tank mounted on locking casters, overall height: 49 in., (ID:7355,Mandatory Loading Fee: $50)
Chester Jensen Tank, mod. x70N50, 20 gallon, center discharge: 4 in. reduced to 2 in. tri clamp (with valve), with top entry scrape agitator, motor: 5 hp, 230/460 volt, 100 rpm approx., with stainless steel control panel, with variable speed drive, additional port for secondary mixer, (Subject to Confirmation)(ID:8245,Mandatory Loading Fee: $75)
Feldmeier Tank, 20 gallon, interior dimensions: 18 in. diameter x 25 in. straight side, slope bottom to end discharge: 1 in., open top (no lid), with bracket for clamp on mixer, with stainless steel grab handles, tank mounted on locking casters, overall height: 49 in., (ID:7350,Mandatory Loading Fee: $50)
Tank, 6000 gallon, interior dimensions: 9 ft. 6in. diameter x 11 ft. 3in. straight side, top and bottom side manways with lids, with top cip spray ball, slope to middle & bottom end discharge: 3 in. tri clamp, side wall gauge: 16, bottom gauge: 11, spray foam insulated bottom, shipping dimensions: 11 ft. wide x 14 ft. long x 11 ft. high, weight empty: 3200 lbs approx., unused, never put into service, interior welds are not food grade polished (Subject to Confirmation) (ID:8454,Mandatory Loading Fee: $500)
Tank, 6000 gallon, interior dimensions: 9 ft. 6in. diameter x 11 ft. 3in. straight side, top and bottom side manways with lids, with top cip spray ball, slope to middle & bottom end discharge: 3 in. tri clamp, side wall gauge: 16, bottom gauge: 11, spray foam insulated bottom, shipping dimensions: 11 ft. wide x 14 ft. long x 11 ft. high, weight empty: 3200 lbs approx., unused, never put into service, interior welds are not food grade polished(Subject to Confirmation) (ID:8455,Mandatory Loading Fee: $500)
Jacketed Tank, 200 gallon, jacketed for cooling, insulated with stainless steel clad, interior dimensions: 39 in. wide x 89in. long x 30.5 in. deep, open top with lid, end discharge: 1.5 in. tri clamp, mounted on a carbon steel platform with stair case, shipping dimensions: 76 in. wide x 112 in. long x 90 in. high at 2000 LBS (ID:7650,Mandatory Loading Fee: $50)
Tank, 350 gallon, dimensions: 45.5 in. diameter x 48 in. straight side, plus cone bottom, center discharge: 2 in., reduced to 1 in. with ball valves, top manway with lid: 19in., with integrated forklift tubes, overall height: 100 in., shipping information: 48 in. wide x 48 in. long x 107 in. high at 1500 LBS (ID:7761,Mandatory Loading Fee: $50)
Tank, 75 gallon dimensions: 24 in. diameter x 38 in. straight side, open top, no lid, top opening: 16 in. diameter, off centered cone discharge: 2 in. with butterfly valve, with grab handles, on casters, overall height with casters: 49 in. (ID:7693,Mandatory Loading Fee: $50)
Cleavland Range tank,mod. TMKDL 150T, 300 gallons, jacket pressure rating: 35 psi at 281 degree fahrenheit, national board no. 21895 & 21896, crn no. H6466.56, direct steam model, center discharge: 3 in. tri clamp, interior dimensions: 40 in. diameter x 36 in. deep, built in agitator system (requires anchor), power tilting mechanism (Subject to Confirmation)(ID:9729,Mandatory Loading Fee: $50)
Tank, 30 gallon, interior dimensions: 30 in. diameter x 25 in. straight side, dish bottom, tank has a screen welded 11.5 in. from the top, center discharge: 1.5 in. tri clamp with valve, bottom ports: two 4 in. tri clamp, open top, mounted onto stainless steel frame with casters, shipping dimensions: 48 in. x 48 in. x 52 in. 500 lbs (ID:8396,Mandatory Loading Fee: $50)
Kettle, 100 gallon, interior dimensions: 45 in. diameter x 26 in. deep, with bracket for clamp on mixer, center discharge, open top with lid, top lid opening: 6 in., no name plate, jacket has been pressure tested, shipping dimensions: 48 in. wide x 52 in. long x 61 in. high at 350LBS (ID:8038,Mandatory Loading Fee: $50)
Jacketed Tank, 13 gallon, dimensions: 17 in. diameter x 24 in. deep, open top, dish bottom, with lid, 1.5 in. center discharge, tri clamp fitting, tank has bracket to mount a mixer, tank is on three stainless steel legs with casters, comes with two ball valves for jacket piping, overall height: 46 in., (ID:5871,Mandatory Loading Fee: $50)
Siebtechnik Jacketed, mod. Short Bowl Decanter, type: sbd 210, serial no. 7287, max drum speed: 5000 rpm, with control panel, with 8 in. orbniox stainless steel valve, with stainless steel support frame, includes manufacturers drawings, data sheets & manuals, equipment refurbished by 2020, stainless steel contact parts (Subject to Confirmation) (ID:7066,Mandatory Loading Fee: $50)
Bepex, mod. Rp 12 k122, design feed rate: 313 kg/hr, motor: 30 hp, 575 volt, 3520 rpm, ul listed motor for hazardous locations, inlet: 10 in. + 3 in. tri clamp, outlet: 20 in. x 6 in., with killark enclosure box, 45 degree base angle hammer mill, 304 stainless steel, mounted onto a stainless steel base with pad, complete manufacturers documentation & drawings available, appears unused (Subject to Confirmation)(ID:7620,Mandatory Loading Fee: $50)
Tilting Kettle, 12 gallon, Stainless Steel, jacket pressure rating: 50 psi @ 298 degree fahrenheit, national board no. 64713, crn no. oh2431.58, dimensions: 16in. diameter x 18in. deep, model: dc 12 (2014), tilting kettle with handle, kettle mounted on a stainless steel stand, (ID:6570,Mandatory Loading Fee: $50)
Jacketed Tank, 5 gallon, jacket rated: 45 psi at 650 degree fahrenheit, national board no. 4489, dimensions: 12 in. diameter x 12 in. deep, open top with lid, overall height: 40 in. (ID:7268,Mandatory Loading Fee: $50)
Material Transfer & Storage, mod. Material Master Bulk Bag Conditioning System, modern control cabinet including, Allen Bradley PowerFlex VFD, PLC based wiring, safety relays, Power requirements: 575 volt, 3 phase., Shipping information: 84\" wide x 122\" long x 126\"high @ 10,000 lbs interlocks., Power requirements: 575 volt, 3 phase., Shipping information: 8 in. wide x 12 in. long x 126\"high at 10,000 lbs(Subject to Confirmation)(ID:9476,Mandatory Loading Fee: $100)
Grote Slicer, mod. S/A 522, Type: Multi lane forming / portioning machine, Configuration: Approx. 4 lane forming system, Construction: Stainless steel, Features:, Multi lane high capacity production, Consistent portion control and forming, Adjustable forming components, Heavy duty industrial design, Operator control panel with hydraulic and drive controls, Sanitary stainless steel construction (ID:9726,Mandatory Loading Fee: $50)
Bizerba Silcer, mod. A500, Type: Automatic slicer, Power: 1.4 kW, Voltage: 208V, 3 Phase, Construction: Stainless steel, Features:, Automatic product feed system, Consistent slice thickness control, Industrial grade construction, Integrated control panel (ID:9728,Mandatory Loading Fee: $50)
Tank, 450 gallon, Polypropylene, interior dimensions: 33 in. x 45 in. x 70 in. high, top inlet, no lid: 10 in. , discharge: 2 in. , stainless steel frame with lifting lugs, integrated forklift slots, overall height: 91 in. , shipping dimensions: 48 in. wide x 50 in. long x 96 in. high at 1000 LBS (ID:7434,Mandatory Loading Fee: $50)
Stainless Steel Hopper, interior dimensions: 22 in. diameter x 16 in. deep, top inlet: 10 in. , discharge: 4 in. , side port: 2.5 in. (ID:8430,Mandatory Loading Fee: $50)
Fluid Air Fluid Bed Dryer, mod.20L, Type: Fluid Bed Dryer / Granulator Stainless Steel Fenwal Ex 200 System , Control system Fenwal Ex 200 explosion protection panel, PLC I/O rack, VFD blower control, The system includes a polished stainless steel process chamber, integrated blower/heater assembly, PLC based controls, and a, Fenwal Ex 200 explosion protection panel, ., Dryer Chamber, Stainless steel drying bowl with clamp down lid, Multiple sight glasses & instrumentation ports, Sanitary product contact surfaces, Stainless discharge cone, Process & Heating System, Ametek blower motor & housing, Integrated electrical heater package, Pneumatic actuators and sanitary valves, Explosion vent / pressure relief features, Controls, Fenwal Ex 200 Explosion Protection System, PLC based control rack, VFD blower control, Digital HMI touchscreen interface, Full stainless control panel enclosure, Safety interlocks & emergency stop (Subject to Confirmation) (ID:9479,Mandatory Loading Fee: $50)
Vibrating Hopper, 20 Cu.ft., 150 gallon, Stainless Steel, interior dimensions: 60 in. diameter x 24 in. deep, discharge: 8in. with butterfly valve, with electric vibrating motor, power requirements: 1 hp, 575 volt, 1800 rpm, (ID:8456,Mandatory Loading Fee: $50)
Kettle, interior dimensions: 42 in. diameter x 10 in. straight side 24 in. deep dish, with bracket for clamp on mixer, discharge: 4.5 in. discharge reduced to 2 in. ball valve tri clamp, open top, no name plate, jacketed kettle: one of the jacket ports has remnants of old threading still lodged in the connection., shipping dimensions: 48 in. wide x 48 in. long x 52 in. high at 500LBS (ID:8511,Mandatory Loading Fee: $50)
Tank (Hopper), 360 gallon, interior dimensions: 72 in. x 72 in. x 16 in. straight side, plus 17 in. cone bottom, discharge: 6 in. , overall dimensions: 76 in. wide x 76in. long x 57 in. high, distance from discharge to floor: 24 in. (ID:8518,Mandatory Loading Fee: $50)
Tank (Hopper), 2250 gallon (300 Cu.Ft.) with Blender & Rotary Valve, Carbon Steel, receiving hopper interior dimensions: 92 in. diameter x 88 in. deep, product inlet: 5 in. , hopper equipped with carbon steel blender, with carbon steel rotary valve, power requirements: 575 volt, with two Semco impactors, hopper has load cells (no controls), overall dimensions: 123 in. x 126 in. x 183 in. high (Subject to Confirmation) (ID:8371,Mandatory Loading Fee: $750)
Lot of Kettles (ID:9400,Mandatory Loading Fee: $50)
Tank (Hopper), 20 gallon, Stainless Steel, interior dimensions: 24 in. diameter x 6 in. straight side, plus 18 in. cone bottom, discharge: 2 in. tri clamp, overall height: 38 in. , distance from discharge to floor: 10 in. (ID:9408,Mandatory Loading Fee: $50)
Tanks, 175 gallon, dimensions: 42 in. diameter x 34 in. straight side, open top tank with dish bottom, side inlet: 2.5 in. tri clamp, center discharge: 3 in. tri clamp, tank is on four stainless steel legs with pads, overall height: 54 in. , shipping information: 48 in. wide x 52 in. long x 60 in. high (ID:9743,Mandatory Loading Fee: $50)
Tank, 275 gallon, dimensions: 41.5in. diameter x 46in. straight side, open top tank with dish bottom, center discharge: 3 in. tri clamp, four (4) stainless steel mixing baffles inside, tank is on four stainless steel legs with pads, overall height: 74 in. , (ID:9744,Mandatory Loading Fee: $50)
Tank, 275 gallon, dimensions: 41.5in. diameter x 46in. straight side, open top tank with dish bottom, center discharge: 3 in. tri clamp, four (4) stainless steel mixing baffles inside, tank is on four stainless steel legs with pads, overall height: 74 in. , (ID:9745,Mandatory Loading Fee: $50)
Mepaco Jacketed Double Ribbon Blender, mod. Twin Shaft Paddle Blender serial no. M12170, 133 Cubic Feet., steam jacket rated 130 PSI at 375 degree fahrenheit, includes a, column dumper (cart dumper), stainless steel mezzanine with staircase,Jacket rating:, 130 PSI at 375°F, ASME certified Apache vessel, Lid System pneumatically assisted lift up lid, Allen Bradley PowerFlex VFDs, 575 volt 3 phase, Missing one discharge gasket, (2008) (Subject to Confirmation)(ID:8552,Mandatory Loading Fee: $100)
Schneider Jacketed Plow Blender, 116 gallons, 15 Cubic Feet, national board no. g 563, interior drum dimensions: 20in. diameter x 84in. long, 10 stainless steel plows, stainless steel shaft diameter: 5.5in. , inlets: 8 in. , 7 in. x 7 in. , two 4in. , 1in. , center discharge: 7 in. , side discharge: 12 in. x 12 in. , max pressure: 86 psi, max temperature: 392 degree fahrenheit / 44 deg.c, two 14 in. x 18 in. doors on the drum, motor: 5.5 hp, 230/460 volt, 1765 rpm, overall blender dimensions: 4 ft. wide x 10 ft. long x 5 ft. high, with 82 in. x 123 in. safety rail, stainless steel contact parts, shipping information: 86 in. wide x 144 in. long x 68 in. high at 3500 LBS (ID:5785,Mandatory Loading Fee: $100)
Rotating Drum Tumbler, interior dimensions: 76 in. diameter x 60 in. deep, with baffles, opening: 36 in. with cover, with control box with tumbler & screw conveyor, motor: 10 hp, 575 volt, tumbler weight empty: 8000 lbs approx., contact parts : stainless steel, with stainless steel screw conveyor, polypropylene screw: 8 in. diameter x 68in. long, mounted on a stainless steel frame with casters, discharge: 9 in. , infeed section: 45 in. long, 115 volt motor, link to test video: https://www.youtube.com/watch?v=pFKxfzH6ubA&ab_channel=Carter WilsonEquipmentServicesInc, ., shipping information: 1 piece at 40 in. wide x 70 in. long x 70 in. high at 600 LBS (Subject to Confirmation)(ID:7528,Mandatory Loading Fee: $100)
Kettle Scrape Surface Agitator,, motor: 2 hp, 330/575 volt, 1740 rpm, gear reducer ratio: 31.23/1, output rpm: 56, stainless steel shaft diameter: 2.25 in. , two sets of 12 scrapers, each scraper dimensions: 2 in. x 4 in. , mixer appears to be unused, dimension top of anchor, from tip to tip of scrapers fully extended : 50 in. (ID:6186,Mandatory Loading Fee: $50)
High Shear Disperser, Motor: 2 hp, 208.230/460 volt, 1725 rpm, with quick connect plug, stainless steel shaft length: 31 in. , stainless steel impeller diameter: 6 in. , with start/stop switch, air/hydraulic lift, overall height when raised: 60in. , max lift height: 35.5 in. , distance from shaft to main support frame: 13.5 in. , overall length: 24 in. (ID:7505,Mandatory Loading Fee: $50)
Ribbon Blender, 1 Cubic Foot, 1 hp, 575 volt, 1725, final output: 86 approx., with variable speed drive, interior dimensions: 14 in. x 10 in. x 12 in. deep, with lid, top inlet in., center discharge: 4 in., mounted on casters, (Subject to Confirmation) (ID:8328,Mandatory Loading Fee: $50)
Airex Dust Collector, mod. 16r8, with (16) 4 in. diameter x 100 in. long cages & new bags, with ul listed solenoid valves, with explosion vent, discharge: 6 in. , overall dust collector dimensions: 48 in. diameter x 172 in. High (ID:7885,Mandatory Loading Fee: $150)
Spray Dynamics Clog Free Slurry Applicator, 18 in. wide x 90 in. long stainless steel belt conveyor, with conveyor speed controller, stainless steel collection pan, with polypropylene diaphragm liquid recirculation pump, with pump controller, with eight pneumatic spray nozzles (4 top & 4 bottom), mounted on a stainless steel frame with casters, (ID:7531,Mandatory Loading Fee: $75)
Rotating Drum Tumbler, interior dimensions: 60 in. diameter x 87 in. long, with interior stainless steel baffles, with control box (forward, reverse, timer, emergency stop), motor: 3 hp, 230/460 volt, 40 rpm approx., contact parts: stainless steel, tumbler mounted on a carbon steel frame, frame foot print: 60 in. x 80 in. , shipping dimensions: 70 in. wide x 102 in. long x 72 in. high at 2000 LBS,link to test video:https://www.youtube.com/watch?v=aC yYafsjRo&ab_channel=Carter WilsonEquipmentServicesInc. (ID:7532,Mandatory Loading Fee: $50)
Patterson Jacketed Ribbon Blender, serial no. 80ca4619.1, total capacity: 120 cu.ft. approx, working capacity: 80 cu.ft. approx., jacket rating: 15 psi, interior blender dimensions: 48in. wide x 144 in. long, top ports: 18 in. , 12 in. , blender is insulated, motor for hazardous locations: 15 hp, 575 volt, 870 rpm, with lifting lugs, shipping weight: 12,000 lbs approx., carbon steel contact parts, shipping information: 5 ft.5 in. wide x 14 ft. long x 6ft.1 in. high (Subject to Confirmation)(ID:7711,Mandatory Loading Fee: $100)
Bepex Jacketed Paddle Dryer/Cooler Crystallizer, mod. solidaire SJS-42-22, serial no. 2017053220 1, four zone jacket rated: 50 psi at 550 degree fahrenheit, vessel rated: 5 psi at 550 degree fahrenheit, asme rated, national board no. 426942, crn no. r4142.5, motor: 75 hp, 575 volt, 275 output rpm, four rows of 142 paddles, 304 stainless steel, interior process surface area dimensions: 42 in. diameter x 22 ft. long, motor control panel available, manufacturers documentation available, unused never put into service, approximate shipping weight: 20,000 lbs (Subject to Confirmation) (ID:7621,Mandatory Loading Fee: $1500)
Lightnin, mod. EV5L33, motor: 0.33 hp, 115/230 volt, 1725 rpm, output rpm: 300 approx., mixer only (ID:8403,Mandatory Loading Fee: $50)
Chromalox Nitrogen Gas Heater, mod. gchssb 03 006p e2xx, 600 volt, 6 kw, 3 phase, with hazardous locations junction box, nitrogen gas flow rate: 198 lb/hr, temperature in: 126 degree fahrenheit, temperature out: 320 degree fahrenheit, material of construction: stainless steel, manufacturers drawings and documentation available, like new (ID:7619,Mandatory Loading Fee: $50)
Ametek Regenerative Blower, mod. Hie454 fr86mlra, scfm: 90, static pressure: 20in. wc, ul listed motor: 1.5 hp, 575 volt, 3500 rpm, explosion proof, inlet & outlet: 2in. npt, like new (ID:7617,Mandatory loading Fee: $50)
Scott Dominator Crusher Shredder, mod. dominator cr30x30ss, sanitary 316l stainless steel construction, with eight (8) cip spray balls (four top, four bottom), motor: 20 hp, 575 volt, 1775 rpm, output rpm: 25 approx., with lifting lugs, (Subject to Confirmation)(ID:7865,Mandatory Loading Fee: $50)
Twin screw conveyor/Lump breakers, inlet: 21 in. x 36 in. , xp motor: 5 hp, 575 volt, 66 rpm approx., two 8 in. discharges, carbon steel contact parts, (ID:8373,Mandatory Loading Fee: $50)
Union Process, mod. Szegvari Attritor Mill, serial no. 110602, Size Q6, grinding tank capacity: 8.2 gallons, media volume: 7.5 gallons, with control panel, with variable speed drive, UL listed motor for hazardous locations: 10 hp, 208.230/460 volt, 1170 rpm, with spare grinding media, with forklift tubes(Subject to Confirmation)(ID:7948,Mandatory Loading Fee: $50)
Hobart Tilting Kettle, mod. VGTRS, 35 gallon, power requirements: 120 volt, gas type : propane, BTU/HR total: 85,000, manual tilting kettle, with lid, with handle, (ID:8484,Mandatory Loading Fee: $50)
Eriez vibratory feeder, motor: 3 hp, 230/460 volt, 1760 RPM, gearbox ratio 48.46:1, ratio 6.5:14 (ID:9420,Mandatory Loading Fee: $50)
Screw conveyor, screw dimensions: 10in. diameter x 62in. long, discharge height: 38in., discharge spout: 8in. diameter x 13in. high, start switch can be timed for operated with foot pedal, motor: 5 hp, 230/460 volt, 1735 rpm, output ratio: 31:1, output rpm: 56 rpm approx., stainless steel feed cone hopper: 13in. 8in. diameter x 14in. high, all stainless steel construction, mounted on 4 stainless steel legs with casters, shipping information: 48in. wide x 96in. long x 78in. high, link to test video:, https://youtu.be/ALpDV8NzEe4(ID:9754,Mandatory Loading Fee: $50)
FPEC Vacuum Tumbler, Model VT-85, serial no. 2853, capacity: up to 5000 lbs approx., interior tumbler dimensions: 65 in. diameter x 72 in. straight side, front load, motor: 10 hp, 575 volt, 1765 rpm, reducer ratio: 37.19/1, output rpm: 47 approx., 304 stainless steel contact parts, shipping information: 7 ft.10 in. wide x 11 ft.1 in. long x 8 ft. 11in. high at 8000 LBS (Subject to Confirmation) (ID:8509,Mandatory Loading Fee: $100)
Sipromac sealer, c/w Busch R5 vacuum pump, stainless steel contact parts, high throughput double chamber packaging system (ID:9719,Mandatory Loading Fee: $50)
Bowl Cutter, motor: 7.5 hp, 575 volt, 3400 rpm, stainless steel contact parts (ID:9720,Mandatory Loading Fee: $50)
Handtmann Stuffer, mod.vf200, (7825) sold for parts, capacity: up to 5,000 kg/h, portion range+D82+D81
Handtmann stuffer (Model 7814) sold for parts, capacity: up to 10,000 kg/h, portion range: 5 to 100,000 g, filling pressure: up to 35 psi, with side bin loader (200 liter meat bins), power requirements: 575 volt, with quick connect plug and electric foot pedal, (ID:9722,Mandatory Loading Fee: $50)
Alfa Laval Desludger Disc Centrifuge, Model BTPx 205SGD-34-CDP-60, serial no. 4036821, with control panel, motor for hazardous locations: 7.5 hp, 230/460 volt, 3490 rpm, documentation available (Subject to Confirmation) (ID:8475,Mandatory Loading Fee: $50)
Mac Dust Collector, mod. 54avs9 2,with fan:, mod. 12sb 4, motor: 2 hp, 230/460 volt, 3460 rpm, bin vent/ silo, pulse jet, approximately 67 square feet filter area, approximately 335 cfm, stainless steel construction, with fan:, (ID:6333,Mandatory Loading Fee: $50)
Feldmeier Blender, 300 gallon, (40 cu.ft), interior blender dimensions: 48 in. wide x 48 in. long x 36 in. deep with a 10 in. cone bottom, top inlets: 3 in., 3 in. with two CIP ball tri clamps, hinged lid with safety grate: 25 in. wide x 34 in long, bottom discharge: 2.5 in. tri clamp, motor: 40 hp, 230/460 volt, 1775 RPM, impeller diameter: 10 in. , material of construction: 304 stainless steel, approx empty weight: 1650 lbs, shipping dimensions: 58 in. wide x 96 in. long x 108 in. high at 2000 LBS (Subject to Confirmation) (ID:8491,Mandatory Loading Fee: $50)
Tranter Plate Heat Exchanger, mod. Ux 226 uj 42, serial no. sb 773, working pressure:125 psi at 212 degree fahrenheit, national board no. 36693, crn no. d3827.6, stainless steel plates, 42 plates: 16 in. wide x 49.5 in. High (ID:5365,Mandatory Loading Fee: $50)
Shick Esteve Dust Collector, mod.8 iqc 700, serial no. cs 01025 001, rating: nema 4x, number of fitler elements: 8, filter elements: spun bonded polyester with eptfe membrane and 99.9% efficiency rating, filter area: 74 sq.ft. approx., recommended cfm range: 444 to 593, max cfm: 741, bottom discharge: 8in. , front manway: 18 in. , with vibco impactor, overall height: 8 ft., material of construction: stainless steel, mounted on four carbon steel legs, (ID:6875,Mandatory Loading Fee: $100)
Eimco Filter Press, Recessed Plate, Gasketed, 470 Mm x 470 Mm, capacity: 1.5 cubic feet approx., plate size: 470 mm x 470 mm, 8 polypropylene gasketed plates, with stainless steel piping and ball valves, one 2 in. center hole, four 1.2 in. corner holes (Subject to Confirmation) (ID:8165,Mandatory Loading Fee: $50)
Hauser high viscocity pneumatic double piston filler, all stainless steel, adjustable height, inlet & outlet: 2 in. x 1.5 in. tri clamp, with attachment, stroke range: 10 oz to 1 liter (ID:7272,Mandatory Loading Fee: $50)
Hoffman Dust Collector, including: primary separator, pulse air dust separator, centrifugal multi stage exhauster & control panel, primary separator with dust collection bin, pulse air dust separator with collection bin & 10 cages (6 in. diameter x 60 in. tall), centrifugal multi stage exhauster, model: 4110 b, motor: 15 hp, 575 volt, 3540 rpm, with control panel (ID:7244,Mandatory Loading Fee: $75)
Dorner Belt Conveyor, dimensions: 32 in. wide x 104 in. long, cleat depth: 1 in. , distance between cleats: 12 in. , stainless steel drip tray, stainless steel motor: 1 hp, 208.230/460 volt, 1750 rpm, stainless steel gearbox reducer, with stainless steel control box, pneumatic raise/lower capability, with stainless steel chute, mounted on a stainless steel frame with locking casters, with spare parts, conveyor is unused, like new, link to test video:, https://www.youtube.com/watch?v=68pjRpLJWgY&ab_channel=Carter WilsonEquipmentServicesInc, . (Subject to Confirmation) (ID:7296,Mandatory Loading Fee: $100)
Used Pall Cartridge Filter, 2 in. x 2 in. max psi: 275 psi at 100 degree fahrenheit, national board no.47120, 316l stainless steel contact parts, a four (4) cartridge model (ID:5614,Mandatory Loading Fee: $50)
Belt Conveyor, cleated belt dimensions: 24 in. wide x 140 in. long inclined straight side plus 30 in. bottom infeed side, discharge height: 90 in. approx., cleat depth: 2 in. , distance between cleats: 11 in. , infeet height: 4 ft. approx., conveyor angle: 20 degrees approx., stainless steel drip tray, currently hydraulically driven (ID:7558,Mandatory Loading Fee: $100)
Dynamic Cooking Systems Commercial Oven, mod. Dcs fs6, power requirements: 240 volt, 3 phase, chamber volume: 29 in. wide x 24 in. high x 27 in. deep, mounted on a stainless steel frame, link to test video:, https://www.youtube.com/shorts/lWLGz3mTZM4 (ID:7605,Mandatory Loading Fee: $50)
Schenck Process Dust Collector, mod. 19avrc4 filter, a four (4) cartridge model, discharge: 8 in. diameter, material of construction: stainless steel, mounted on a stainless steel frame: 33 in. x 54 in. , shipping information: 48 in. wide x 66 in. long x 88 in. high at 500 LBS (ID:7132,Mandatory Loading Fee: $50)
Paul Mueller Heat Exchanger, Tube & Shell, Full Vacuum, serial no. 357150 17, national board no. 42994, shell side mawp: 125 psi at 600 degree fahrenheit, tube side mawp: 150 psi at 400 degree fahrenheit, rated full vacuum, u tube design, stainless steel tubes, 238 in. long, number of tubes : 13, stainless steel contact parts, overall length: 248 in. long, ports: four 2 in. flanged, two 1 in. npt, shipping dimensions: 25 in. wide x 250 in. long x 12 in. high at 1500 LBS (2007) (ID:7392,Mandatory Loading Fee: $50)
Pall Centramate CM500S Tangential Flow Filtration System, serial no. 04.00275.01, max working volume (5 l), min working volume (170 ml), pressure range: 0 to 87 psi, temperature range: 0 to 45 degree celcius (32 degree fahrenheit to 113 degree fahrenheit), flow rate: 15 to 600 l/hr, power requirements: 115 volt, refer to pdf product brochure for more information (Subject to Confirmation)(ID:7580,Mandatory Loading Fee: $50)
Belt Conveyor, cleated belt dimensions: 54 in. wide x 70 in. long, infeed/discharge height: 52 in., retractable stainless steel side guards, with cip spray bar, stainless steel motor: 0.5 hp, 575 volt, 1750 rpm, stainless steel gearbox reducer, mounted on a stainless steel frame (ID:7668,Mandatory Loading Fee: $50)
Belt Conveyor, 2 in. deep, with full stainless steel drip dray, side polypropylene guard rails, discharge height: 5 ft., top stainless steel hopper: 30 in. wide x 70 in. long x 14 in. deep, motor: 1 hp, 575 volt, 4 rpm approx., mounted on a stainless steel frame with casters, link to test video:, https://www.youtube.com/watch?v=tVQjFHiWDMc&ab_channel=Carter WilsonEquipmentServicesInc,. (ID:7669,Mandatory Loading Fee: $50)
Belt Conveyor, motor: 0.75 hp, 575 volt, 1750 rpm, reducer ratio: 17.62/1, final output rpm: 99 approx., infeed & outfeed height from belt to floor: 32 in. & 35 in. , adjustable side guards, stainless steel frame (ID:7824,Mandatory Loading Fee: $50)
Belt Conveyor, belt dimensions: 8in. wide x 50in. long, motor: 0.3 hp, 230 volt, 1750 rpm, reducer ratio: 10/1, final output rpm: 175 approx., with quick connect plug, with on/off switch, stainless steel frame on casters (ID:7689,Mandatory Loading Fee: $50)
Belt Conveyor, food grade platic mesh belt dimensions: 9 in. wide x 16 ft. 4 in. long, infeed & outfeed height: 38 in. , stainless steel side rails, motor: 1 hp, 208 volt, 1740 rpm, reducer ratio: 38.23/1, output rpm: 0 46 approx., with allen bradley variable speed drive, mounted on a stainless steel frame with locking casters (ID:7726,Mandatory Loading Fee: $150)
Belt Conveyor, belt dimensions: 12 in. wide x 176 in. long, motor: 0.75 hp, 115/230 volt, 1 phase, with 230 volt quick connect plug, discharge height: 45 in. , carbon steel frame (ID:7854,Mandatory Loading Fee: $50)
Twin shaft stainless steel screw conveyor, inlet: 5.75 in. x 9.5 in. , outlet: 4 in. , motor: 230/460 volt, 1725 rpm, stainless steel contact parts (ID:7926,Mandatory Loading Fee: $50)
Semco Dust Collector, mod. vf 150, number of cartridges: 3, with impactor, with schenck process carbon steel rotary airlock valve, inlet & outlet: 8 in. , model: ram08, xp motor: 0.75 hp, 575 volt, material of construction: carbon steel (ID:7709,Mandatory Loading Fee: $50)
Belt Conveyor, belt dimensions: 42 in. wide x 115 in. long, infeed / discharge height: 40 in. high, motor: 2 hp, 575 volt, 52 rpm approx., with cip bar, with stainless steel control panel, stainless steel frame with casters (ID:7729,Mandatory Loading Fee: $50)
Manning & Lewis Reboiler Heat Exchanger, serial no. 166523, national board no. 6158, tube mawp: 150 psi at 400 degree fahrenheit, shell mawp: 250 psi at 150 degree fahrenheit, number of tubes : 91 in. u tubesin. , tube diameter: 0.75 in. , new interior coating, ports: seven (7) 2 in. , one (1) 1.5 in. , asme rated, manufacturers drawings available, weight empty: approx. 6000 lbs (Subject to Confirmation)(ID:8168,Mandatory Loading Fee: $100)
Belt Conveyor, Belt dimensions: 6 in. wide x 84 in. long, Discharge height: 48in. , With variable frequency drive, Power requirements: 120 volt, Motor: 230/460 volt, output rpm: 0 to 112 RPM, With quick connect plug, With on/off switch, Stainless steel frame with casters, Side wall height: 4 in., Solid stainless steel in. Uin. shape sidewall + belt support frame, (ID:7724,Mandatory Loading Fee: $)
Omega Head Bottle Sorter Unscrambler, mod. 3D RP1 8, serial no. 85 1670, 8 head bottle unscrambler sorter, with blower (bottle cleaner), with control panel, with turning feed table & chute, with outfeed conveyor section (requires motor and belting), stainless steel construction, power requirements: 115 volt (ID:7991,Mandatory Loading Fee: $)
Progressive Recovery (PRI) Vacuum Distillation Unit, mod. SCR 200E, Capacity: 75 gallons, 575V, explosion proof motors, With scraper system, 304 stainless steel, primed and painted with a cross linked polyurethane, Electrical and mechanical temperature sensors, Self contained internal heating oil and elements, Vacuum pump not included (Subject to Confirmation)(ID:8169,Mandatory Loading Fee: $100)
Meco Heat Exchanger, Tube & Shell, Stainless Steel, number of tubes : 56, 85.75 in. long, 0.25in. diameter, tube inlet & outlet: 1 in. , shell inlet & outlet: 1.25 in. (ID:8338,Mandatory Loading Fee: $50)
PDC Neck Bander, mod. 45M, serial no. 147, 115 volt, seal applicator that can apply heat srink bands and sleeves at speeds of up to 80 pieces per minute. (ID:8466,Mandatory Loading Fee: $50)
Rotary Air Lock Valve, 8 in. x 8 in., inlet & outlet : 8 in. , xp motor: 0.5 hp, 575 volt, with stainless steel lump breaker (ID:8375,Mandatory Loading Fee: $50)
Belt Conveyor, power requirements: 90 volt, DC, output rpm: 42 approx., cleated belt dimensions: 6 in. wide x 70 in. long, cleat depth: 1.5 in. , stainless steel feed hopper: 34 in. x 30 in. x 18 in. deep, infeed height: 42 in. , discharge height: 60 in. approx, with discharge chute, mounted stainless steel frame with casters, shipping information: 48 in. wide x 80 in. long x 90 in. high 750 lbs(ID:8547,Mandatory Loading Fee: $50)
Vibratory Feeder, top feed hopper: 24 in. x 24 in. x 24 ft., plus 16 in. deep cone bottom, 115 volt power requirement, with magnetic fingers at discharge, vibratory feeder: 4 in. wide x 20 in. long, with integrated forklift tubes, carbon steel contact parts, with magnet manufacturing(ID:9670,Mandatory Loading Fee: $50)
Belt Conveyor, belt dimensions: 7.5 in. wide x 38 in. long, charge / discharge height: 30 in. high, motor: 120 volt, with variable speed motor controller, stainless steel frame, (ID:9723,Mandatory Loading Fee: $50)
Belt Conveyor, food grade plastic belt with cleats, discharge height: 68 in., stainless steel drum motor: 0.75 hp, 460 volt, variable speed, with allen bradley variable frequency drive, with quick 480 volt connect plug, with foot switch, stainless steel frame mounted on casters, with adjustable legs, (ID:6836,Mandatory Loading Fee: $75)
Rosedale Products inc. Basket Filter, mod. NC08 30 11/2SAN 2 150 S, pressure rating: 150 psig, basket dimensions: 6.5 in. diameter x 26 in. straight side, inlet & outlet: 1.5 in. tri clamp, center bottom outlet: 1 1/4 in. npt parallel fitting, (ID:9666,Mandatory Loading Fee: $50)
Fristam Centrifugal Pump, inlet & outlet: 3 in. x 2.5 in. tri clamp, motor: 15 hp, 230/460 volt, 1760 rpm, stainless steel contact parts(ID:6797,Mandatory Loading Fee: $50)
Fristam Centrifugal Pump, inlet & outlet: 3 in. x 2.5 in. tri clamp, motor: 15 hp, 230/460 volt, 1760 rpm, stainless steel contact parts(ID:6798,Mandatory Loading Fee: $50)
Fristam Centrifugal Pump, inlet & outlet: 3 in. x 2.5 in. tri clamp, motor: 7.5 hp, 230/460 volt, 1760 rpm, stainless steel contact parts (ID:6799,Mandatory Loading Fee: $50)
Syntron Vibratory Magnetic Feeders, mod. f t01, with two syntron magnetic feeders, model: f t01, 115 volt, with nucon vacuum system, with control panel, mounted on a carbon steel frame, previous use: industrial application(ID:7459,Mandatory Loading Fee: $50)
Rotary Drum Screen, Variable Speed, stainless steel rotary drum screen dimensions: 30 in. diameter x 48 in. long, overall screen length: 55 in. , slot screen: 1 in. , with variable frequency drive, power requirements: 115 volt, material of construction: stainless steel, bottom removable collection pan: 36in. x 34in. , mounted on stainless steel frame with casters, link to test video:, https://www.youtube.com/shorts/mOoTxvw9dUg(ID:7527,Mandatory Loading Fee: $75)
Wrightflow Rotary Lobe Pump, mod. 0300 TRA10, capacity: 11 gpm approx., inlet & outlet: 1.5 in. tri clamp, texp motor: 1.5 hp, 575 volt, 512 output rpm approx., mounted on a stainless steel base, stainless steel contact parts(ID:7903,Mandatory Loading Fee: $50)
Viking Jacketed Gear Pump, inlet & outlet: 2.5 in. , pump only, max flow rate: 80 gpm, carbon steel contact parts, jacketed pump head end plate (ID:7749,Mandatory Loading Fee: $50)
Alfa Laval Plate Heat Exchanger, mod. tl 10 bfg, serial no. 30120 97231, inlet & outlet: in., working pressure: 150 psi at 212 degree fahrenheit, national board no. 52301, crn no. m2262.5c, 20 stainless steel plates : 15 in. wide x 59 in. High (ID:8139,Mandatory Loading Fee: $50)
Custom built filter press, recessed plate, plate size: 900mm x 900mm, 11 polypropelene non gasketed plates, four 1.5 in. corner holes, center hole: 4 in. , with box of new filter clothes, mounted on casters, with stainless steel drip pan, (ID:8036,Mandatory Loading Fee: $50)
Filtrine Manufacturing Closed Loop Chiller, mod. pcp 25 2a, refrigerant: r22, power requirements: 115 volt, 0.25 hp, cooling capacity: btu/hr : 2400, coolant discharge temperature: 68 degree fahrenheit, ambient temperature: 90 degree fahrenheit (ID:8025,Mandatory Loading Fee: $50)
Omega Head Bottle Sorter Unscrambler, mod. 3D RP1 8, serial no. 85 1670, 8 head bottle unscrambler sorter, with blower (bottle cleaner), with control panel, with turning feed table & chute, with outfeed conveyor section (requires motor and belting), stainless steel construction, power requirements: 115 volt (ID:7991,Mandatory Loading Fee: $50)
Graco Uni-Drum Bulk Supply System, 300 gallon (1200 liter) magnadrums, two (2) stainless steel graco severe duty rod and cylinder pumps for abrasive coatings, model dura-flo 2400, xl 10,000, ratio 34:1 (ID:8150,Mandatory Loading Fee: $50)
Sealant Equipment & Engineering (Nordson) Dual Integrated Pneumatic Metering System, mod. 2200 series, meter volume per stroke: 98.9 cubic inches per side, max working pressure: 3500 psi, max flow rate: 4 gpm, documentation available, As per manufacturer:, the IPS was designed to quickly move materials, with viscosities greater than 500,000 CPS ranging up to 2 million., Continuous flow provided by alternating metering cylinders and valve timing on material manifold, Large 2 1/8 in. or 3 in. rods push through material slowly for greatest control of material pressure and output., (ID:8158,Mandatory Loading Fee: $50)
Sealant Equipment & Engineering (Nordson) Dual Integrated Pneumatic Metering System, mod. 2200 series, meter volume per stroke: 98.9 cubic inches per side, max working pressure: 3500 psi, max flow rate: 4 gpm, documentation available, As per manufacturer:, the IPS was designed to quickly move materials, with viscosities greater than 500,000 CPS ranging up to 2 million., Continuous flow provided by alternating metering cylinders and valve timing on material manifold, Large 2 1/8 in. or 3 in. rods push through material slowly for greatest control of material pressure and output., (ID:8159,Mandatory Loading Fee: $50)
Semco Rotary Air Lock Valve, 8 in. x 8 in. Valve only, no motot (ID:8121,Mandatory Loading Fee: $50)
Sealant Equipment & Engineering (Nordson) Dual Integrated Pneumatic Metering System, mod. 2200 series, meter volume per stroke: 98.9 cubic inches per side, max working pressure: 3500 psi, max flow rate: 4 gpm, documentation available, As per manufacturer:, the IPS was designed to quickly move materials, with viscosities greater than 500,000 CPS ranging up to 2 million., Continuous flow provided by alternating metering cylinders and valve timing on material manifold, Large 2 1/8 in. or 3 in. rods push through material slowly for greatest control of material pressure and output.,(ID:8160,Mandatory Loading Fee: $50)
Fulton Heat Exchanger, Tube & Shell, Stainless Steel, tube mawp: 15 psi at 200 degree fahrenheit, shell mawp: 100 psi at 200 degree fahrenheit, number of tubes : 24 in. u tubesin. , 44 in. long (ID:7779,Mandatory Loading Fee: $50)
Viking Gear Pump, mod. K224A, inlet & outlet: 2 in. , motor: 1.5 hp, 575 volt, 1740 rpm, final output rpm: 60 approx., mounted on stainless steel base, carbon steel contact parts (ID:8100,Mandatory Loading Fee: $50)
Viking Gear Pump, mod. K224A, inlet & outlet: 2 in. , motor: 1.5 hp, 575 volt, 1740 rpm, final output rpm: 60 approx., mounted on stainless steel base, carbon steel contact parts(ID:8101,Mandatory Loading Fee: $50)
Top Flo Centrifugal Pump, mod. C328 21TC, inlet & outlet: 3 in. x 2 in. tri clamp, motor: 7.5 hp, 575 volt, 1760 rpm, stainless steel contact parts (ID:8287,Mandatory Loading Fee: $50)
Centrifugal Pump, inlet & outlet: 3 in. x 2 in. tri clamp, motor for hazardous locations: 5 hp, 575 volt, 1760 rpm, , stainless steel contact parts (ID:8286,Mandatory Loading Fee: $50)
Seepex Progressive Cavity Pump, inlet & outlet: 1.5 in. NPT, motor: 575 volt, 1750 rpm (no name plate), reducer ratio: 4.22/1, final output rpm: 415 approx., chamber length: 13.5 in. , carbon steel contact parts, shop tested 575 volt(ID:8421,Mandatory Loading Fee: $50)
Semco Rotary Air Lock Valve, inlet & outlet: 8 in. , housing material: carbon steel, blade material: carbon steel, xp motor: 0.5 hp, 575 volt, 1750 rpm, reducer ratio: 39.62/1, (ID:8377,Mandatory Loading Fee: $50)
Goulds Centrifugal Inline Pump, mod. 10SV5FB30, nominal capacity: 53 gpm, five (5) impeller stages, inlet & outlet: 2 in. , flanged fittings, motor: 5 hp, 575 volt, 3490 rpm (ID:8457,Mandatory Loading Fee: $50)
Goulds Centrifugal Inline Pump, mod. 10SV5FB30, nominal capacity: 53 gpm, five (5) impeller stages, inlet & outlet: 2 in. , flanged fittings, motor: 5 hp, 575 volt, 3490 rpm (ID:8458,Mandatory Loading Fee: $50)
Lindberg / Blue M Gravity Oven, mod. GO1310SA-1, temperature range: 40c to 260c, power requirements: 120 volt (ID:8481,Mandatory Loading Fee: $50)
Goulds Centrifugal Pump, mod. ESHC 3x4x8 4P PM, catalog number: 03SH08A10T4H2, inlet & outlet: 4 in. x 3 in., flange fittings: 9 in. x 8 in. , impeller diameter 9.063 in, 316 stainless steel contact parts, motor: 10 hp, 575 volt, 1760 rpm, (ID:9467,Mandatory Loading Fee: $50)
Centrifugal Pump, inlet & outlet: 1.5 in. x 2 in. tri clamp, impeller diameter: 5.5 in. , stainless steel motor: 5 hp, 575 volt, 3525 rpm, stainless steel contact parts,(ID:9407,Mandatory Loading Fee: $50)
Centrifugal Pump, inlet & outlet: 1.5 in. x 1.5 in. x 2 in. tri clamp, impeller diameter: 8 in. , stainless steel motor: 7.5 hp, 575 volt, 1755 rpm, stainless steel contact parts (ID:8514,Mandatory Loading Fee: $50)
Rotary Air Lock Valve, inlet & outlet: 10 in., housing material: carbon steel, blade material: carbon steel, motor for hazardous locations: 0.75 hp, 575 volt, 1730 rpm, output rpm: 45 approx., with stainless steel hopper, (ID:8459,Mandatory Loading Fee: $50)
Rotary Air Lock Valve, inlet & outlet : 8in. , xp motor: 0.75 hp, 575 volt, with stainless steel lump breaker, (ID:8372,Mandatory Loading Fee: $50)
Centrifugal Inline Booster Pump, inlet & outlet: 2 in. with adapters reducing to 1in., motor for hazardous locations: 5 hp, 230/460 volt, 3505 rpm (ID:8507,Mandatory Loading Fee: $50)
Finish Thompson Drum Pump, mod. m7t, stainless contact parts, power requirements: 115 volt (ID:8485,Mandatory Loading Fee: $50)
Sweco Kason Screen, mod. D 6870 1B/C, serial no. 3857, motor: 1 HP, 550 volt, 1155 RPM, base only no decks (ID:7593,Mandatory Loading Fee: $50)
Graco Drum Unloading Pump, mod. premier 800, capacity: 11 gpm, ratio:45 to 1, maximum air pressure: 100 psi, currently equipped with two nozzle attachment (ID:8154,Mandatory Loading Fee: $50)
Graco Drum Pump, mounted on cart (ID:8355,Mandatory Loading Fee: $50)
Graco President Drum Pump, series F10a, max flow rate: 3 gpm, mounted on cart (ID:8353,Mandatory Loading Fee: $50)
Flexicon Hopper / Dump Station, interior dimensions: 36 in. x 36 in. , screw inlet: 3.5 in. , open top with lid, chute and valve, with pneumatic vibrator, carbon steel (ID:8125,Mandatory Loading Fee: $50)
Flexicon Hopper / Dump Station interior dimensions: 36 in. x 36 n. , screw inlet: 4 in. , open top with lid, chute and valve, with pneumatic vibrator, carbon steel (ID:8126,Mandatory Loading Fee: $50)
Tri-Clover Centrifugal Pump, inlet & outlet: 2.5 in. x 1.5 in. tri clamp, motor: 7.5 hp, 208.230/460 volt, 3500 rpm, stainless steel contact parts (ID:8203,Mandatory Loading Fee: $50)
Finish Thompson Drum Pump, mod. m3tv, polypropylene contact parts, power requirements: 115 volt, rpm: 0 12,000, max viscosity: 2000 cp, gpm: 4 to 24 gpm depending on viscosity, max feet of head: 28 to 52 ft depending on viscosity (ID:7764,Mandatory Loading Fee: $50)
Madden Diaphragm Metering Pump, mod. mh1180f, serial no. 45408, washdown motor: 1 hp, 208/230 volt, 1725 rpm, output range: 18 180 gph, max pressure: 100 psi, inlet & outlet: 0.75in. npt, stainless steel contact parts (ID:8029,Mandatory Loading Fee: $50)
Coso High Accuracy Automatic Checkweigher, mod. cw 150, power supply: 110 volt, max check weight: 200g, max speed: 200 pcs/min, suitable product dimensions: 150 mm x 120 mm, with pneumatic air rejector, belt dimensions: 6 in. wide x 40 in. long, stainless steel construction (ID:8024,Mandatory Loading Fee: $50)
MMC Centrifugal Fan, mod. pw14, ul listed motor for hazardous locations: 5 hp, 575 volt, 3475 rpm (ID:8035,Mandatory Loading Fee: $50)
Buhler Rotary Air Lock Valve, model: use 28/30, 8.5 in. x 10.5\", housing & blade material: stainless steel, valve only, no motor (ID:8051,Mandatory Loading Fee: $50)
New Brunswick Scientific Water Bath Shaker, mod. classic c76, power requirements: 120 volt (ID:8034,Mandatory Loading Fee: $50)
Probat-Werke Rotary Air Lock Valve, mod. 46 dn 250 1, inlet & outlet: 10 in. , housing material: carbon steel, blade material: carbon steel, motor: 1 hp, 230/460 volt, 20 output rpm approx., (ID:8050,Mandatory Loading Fee: $50)
Centrifugal Pump, inlet & outlet: 2.5 in. x 2 in. tri clamp, impeller diameter: 5 in. , motor: 3 hp, 575 volt, 3450 rpm, stainless steel contact parts (ID:8081,Mandatory Loading Fee: $50)
Centrifugal Pump, inlet & outlet: 2.5in. x 1.5in. tri clamp, with stainless steel motor cover, motor: 15 hp, 575 volt, 3500 rpm, impeller diameter: 7.5 in. , mounted on stainless steel stand, stainless steel contact parts (ID:7820,Mandatory Loading Fee: $50)
Ametek Regenerative Blower , mod. en523, max cfm: 84 approx., ul listed motor for hazardous locations: 3 hp, 575 volt, 3450 rpm, inlet & outlet: 2 in. npt (ID:7717,Mandatory Loading Fee: $50)
Viking Jacketed Rotary Lobe Pump, mod. r2s, inlet & outlet: 1.5 in. tri clamp, pump head (front plate), pump only, stainless steel contact parts (ID:7740,Mandatory Loading Fee: $50)
Tilting Filter / Strainer, 20 gallon, interior dimensions: 12 in. diameter x 45 in. deep, with lid, drain: 0.5 in. with ball valve, mounted on a stainless steel base with casters, tilting filter / strainer, stainless steel contact parts, (ID:7747,Mandatory Loading Fee: $50)
Tilting Filter / Strainer, 20 gallon, interior dimensions: 12 in. diameter x 45 in. deep, no lid, drain: 0.5 in. with ball valve, mounted on a stainless steel base with casters, tilting filter / strainer, stainless steel contact parts (ID:7748,Mandatory Loading Fee: $50)
Jet Electric Chain Hoist, mod, fa 0.5 s, lift: 15 ft., capacity: 1100 lbs, motor: 1.2 hp, 575 volt, 28 fpm, with remote (ID:7909,Mandatory Loading Fee: $50)
3M Zeta Plus Cartridge Filter, max psi: 150 psi at 212 degree fahrenheit, inlet & outlet: 2 in. tri clamp, 316l stainless steel contact parts, requires cartridge (ID:7868,Mandatory Loading Fee: $50)
Centrifugal Fan, motor: 0.5 hp, 575 volt, 3450 rpm, outlet: 3 in. tri clamp, stainless steel support (ID:7736,Mandatory Loading Fee: $50)
Centrifugal Fan, motor: 0.75 hp, 575 volt, 3500 rpm, outlet: 2.5 in. (ID:7737,Mandatory Loading Fee: $50)
Waukesha Rotary Lobe Pump, mod. 10, inlet & outlet: 1in. (2 in. bevel sanitary thread fitting), motor: 1 hp, 575 volt, 3 phase, stainless steel feed hopper: 24 in. diameter x 26 in. deep, mounted on stainless steel base with casters, stainless steel contact parts (ID:7691,Mandatory Loading Fee: $50)
Stainless Steel Feeder, stainless steel decline feeder: 18 in. wide x 40 in. long, stainless steel feed hopper: 28 in. x 30 in. x 24 in. deep, pneumatic discharge gate, end table: 20 in. x 23 in. , stainless steel frame with casters (ID:7837,Mandatory Loading Fee: $50)
Picard Sheet Cake Deposer, mod. lp 372, feeder hopper: 25 5/8 in. , product discharge: 6.5 in. , cutting bar: 25 5/8 in. , mounted on casters (ID:7950,Mandatory Loading Fee: $50)
Millipore Cartridge Filter, max psi: 150 psi at 300 degree fahrenheit, inlet & outlet: 3 in. tri clamp, top port: 1.5 in. tri clamp, stainless steel contact parts, requires cartridges(ID:7581,Mandatory Loading Fee: $50)
Spx Centrifugal Pump, max capacity: 100 gpm, max head: 44 ft., inlet & outlet: 2.5 in. x 1.5 in. tri clamp, motor: 5 hp, 208.230/460 volt, 1750 rpm, with quick connect plug, stainless steel contact parts(ID:6632,Mandatory Loading Fee: $50)
Goulds Centrifugal Pump, capacity: 110 gpm approx., feet of head: 85 approx., motor: 5 hp, 575 volt, 3500 rpm, inlet & outlet: 3 in. x 1.5 in. flanged, ductile iron, contact parts (ID:6998,Mandatory Loading Fee: $50)
Moyno Progressive Cavity Pump, mod. cfa61 sxjm3 sabe, inlet & outlet: 5/8 in. tri clamp, motor: 1 hp, 230/460 volt, 1750 rpm, reducer ratio: 14.72/1, final output rpm: 118 approx., stainless steel contact parts(ID:6956,Mandatory Loading Fee: $50)
Rotary Air Lock Valve, 8 in. x 8 in., outlet (blow through): 3 in. , housing material: stainless steel, blade material: stainless steel, motor: 0.5 hp, 575 volt, mfg: premier pneumatics, serial no. 11992, previous use: food application(ID:5839,Mandatory Loading Fee: $50)
Shick Rotary Air Lock Valve, mod. t225, inlet 8in., outlet: 8 in. x 8 in. , housing material: carbon steel, blade material: carbon steel, motor: 0.5 hp, 208.230/460 volt, 1140 rpm (missing fan cover), reducer ratio: 60/1, output rpm: 19 approx., (ID:6527,Mandatory Loading Fee: $50)
Toshiba Transistor Inverter Drive, 600 Volt, capacity: 40 kva / 40 hp, input: 600 volt, 45 amps, 60 hz, output: 600 volt, 41 amps, 1 80/400 hz, enclosure type: 1, shipping information: 48 in. wide x 48 in. long x 30 in. high at 300 LBS (ID:7315,Mandatory Loading Fee: $50)
Plenty Mirrlees Waukesha Screw Pump, mod. Ca52-4nl, inlet & outlet: 3 in. x 2 in. , motor: 15 hp, 230/460 volt, 3520 rpm (ID:7097,Mandatory Loading Fee: $50)
Mac Process Rotary Air Lock Valve, mod. md40, inlet & outlet: 10 in. x 10 in. , housing material: carbon steel, blade material: stainless steel, motor: 0.75 hp, 575 volt, 1725 rpm, requires chain, (ID:7457,Mandatory Loading Fee: $50)
(5) Allen Bradley Variable Frequency Drives, mod. powerflex70, four (4) 1 hp, 480 volt, one (1) 5 hp, 480 volt (ID:6981,Mandatory Loading Fee: $50)
Megga Pump Centrifugal Pump, 1.5 HP, inlet & outlet: 3 in. x 2.5 in. , motor: 1.5 hp, 575 volt, 1740 rpm, previous use: mineral processing, carbon steel contact parts (ID:6910,Mandatory Loading Fee: $50)
Mobile Stainless Steel Adjustable Chute, dimensions: 48.5 in. wide x 35 in. long x 2 in. deep, all stainless steel construction, with liquid discharge outlet, chute mounted on a stainless steel frame with locking casters, adjustable discharge chute with five different angle settings (ID:7239,Mandatory Loading Fee: $50)
Mac Process Inline Dry Bulk Magnet Trap, mod. bm2500 rez, length: 36 in., port diameter : 2 in., stainless steel (ID:7135,Mandatory Loading Fee: $50)
Fisher Scientific Lab Oven, mod. 750, series 700, temperature range: 50 to 275 def.c, power requirements: 120 volt, chamber volume: 5 cubic feet, 18in. x 26in. x 18in. deep (ID:7436,Mandatory Loading Fee: $50)
Pyradia Oven, mod. r4p302430tct, max temperature : 500 degree fahrenheit, power requirements: 600 volt, 3 phase, chamber volume: 29.5 in. wide x 24 in. deep x, 38 in. high, overall dimensions: 48 in. wide x 51.5 in. long x 78.5 in. high (ID:7428,Mandatory Loading Fee: $50)
LIGHTNIN EV1P25A - Air mixer(ID:AE48,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
VIDEOJET 1520 - Inkjet coding machine(ID:AE55,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
VERSAMATIC E5AP5T559C - Pneumatic diaphragm pump(ID:AE56,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
UNI-PHARMA - Automatic labeler(ID:AE59,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
NITA JOUST BOTTOM - Bottom labeler(ID:AE60,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
VERSA-MATIC E5AP5T559C - Diaphragm pump(ID:AE62,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
Loma Systems IQ2 - Metal detector(ID:AE63,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
King Technofill - Semi-automatic liquid filler(ID:AE64,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
Control GMC FDS2500 - Cup, tub and tray filling line(ID:AE65,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
prb packaging systems - Palletizer(ID:AE69,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
Semi-automatic capper(ID:AE70,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
SIGNODE LBx2000 - Strapping machine(ID:AF10,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
THE LOVESHAW CORPORATION LITTLE DAVID 4C - Semi-automatic top case/box sealer(ID:AF12,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
NENOTECH BM 16 - Drop sealer(ID:AF18,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
3M-Matic 22A - Semi-automatic top & bottom case/box sealer(ID:BH06,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
DORNER 2200 SERIES 225M041900D0501 - 93in. Urethane belt conveyor(ID:BH12,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
DAMARK SMC 1620 / STB 16A - L-bar sealer & heat tunnel kit(ID:CD04,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
SWAN-MATIC CAP-MASTER - Semi-automatic capper(ID:CD05,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
Markem-Imaje 9020 - Inkjet printer(ID:CD06,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
High Shear inline mixer 25HP(ID:CD08,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
EGGPLANT M/C - Fruit and vegetable cutting machine(ID:DF22,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
ENOS EURO BASE - Automatic labeler(ID:DP17,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
LABEL SYSTEMS LS 100 80 - Top and front security seal labeler(ID:EAG03,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
DAMARK PACKAGING - L-bar sealer and heat tunnel (ID:EAG04,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
ME RE DE INC. - Mascara filling machine(ID:EV08,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
Triopac - Motorized roller conveyor(ID:FR03,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
Semi-automatic piston filler(ID:GF03,Mandatory Loading Fee: $25) (Located at 10 Rue Industrielle, Delson, Quebec)
AL TECH ALLINE C - Automatic labeler(ID:GF12,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
DORNER 2200 SERIES - Elevator conveyor(ID:HL02,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
CASx320 - Industrial scale(ID:HL03,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
Sartorius YDP20-0CE - Laboratory printer(ID:HL04,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
SureTorque S3 LAB - Cap torque tester(ID:HP14,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
Mobile jacketed 227 L (60 GAL) SS316 tank with air mixer(ID:LL03,Mandatory Loading Fee: $50) (Located at 10 Rue Industrielle, Delson, Quebec)
PACKFLO PF-730 - Vertical form fill and seal machine(ID:MM09,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
AEVOS VM-100 - V-Mixer(ID:NEW32,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
AEVOS AULBL-HRZ - Automatic horizontal labeler(ID:NEW40,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
AEVOS RINS-12 - Automatic bottle rinser(ID:NEW52,Mandatory Loading Fee: $Ask for crating fee)(Located at 10 Rue Industrielle, Delson, Quebec)
AEVOS CWBU-1000 - Checkweigher(ID:NEW55,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
JDA PROGRESS - Semi-automatic capper(ID:NT09,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
Elevator conveyor(ID:OSM05,Mandatory Loading Fee: $Ask for crating fee) (Located at 10 Rue Industrielle, Delson, Quebec)
GROEN PT 40 SP. - Stainess steel jacketed tank(ID:PG03,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
ALLCHAMP A368-L - Semi-automatic pie crust pressing machine(ID:PJ13,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
Semi-automatic piston filler with heated hopper and agitator(ID:PP04,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
KALIx-DUPUY K x 00 2889 - Tube filler(ID:PP05,Mandatory Loading Fee: $Ask for crating fee)(Located at 10 Rue Industrielle, Delson, Quebec)
Semi-automatic piston filler(ID:PP06,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
400 L Stainless steel mixing tank with mezzanine(ID:PP07,Mandatory Loading Fee: $Ask for crating fee)(Located at 10 Rue Industrielle, Delson, Quebec)
72in. x 8in. Belt conveyor (ID:PP14,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
WFM-10 - Super fine crushing and vibrating mill(ID:SD122,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
INGERSOLL RAND AR0666100-362C - Air-operated double diaphragm pump(ID:SD125,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
ARO 666100-362-C - Pneumatic diaphragm pump(ID:SD126,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
NEWMAPAK - Elevator conveyor(ID:ST02,Mandatory Loading Fee: $Ask for crating fee)(Located at 10 Rue Industrielle, Delson, Quebec)
Intralox ARB - 120in. Intralox belt convoyeor(ID:ST08,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
MINSHENG T212 - Automatic labeler(ID:DH07,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
FG-5 - Semi-automatic auger filler(ID:DH08,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
ABI System DLA - Automatic wrap-around labeler(ID:AE76,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
Markem-Imaje 9030 IP65 - Inkjet printer(ID:HP05,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
Markem-Imaje 9030 - Inkjet printer(ID:HP06,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
Semi-automatic filler(ID:CD10,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
DGT Solutions ADP4-24 - Automatic case packer(ID:SE01,Mandatory Loading Fee: $Ask for crating fee)(Located at 10 Rue Industrielle, Delson, Quebec)
LEE INDUSTRIES INC. 20A - Stainless steel tank(ID:FS02,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
252in. x 10in. Belt conveyor with sorting table(ID:FS05,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
204in. x 12in. Belt conveyor(ID:FS06,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
HONEMIx HONE TOP -(ID:LP05,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
Semi-automatic security seal labeler(ID:LP08,Mandatory Loading Fee: $25)(Located at 10 Rue Industrielle, Delson, Quebec)
Elevating screw conveyor(ID:NT,Mandatory Loading Fee: $Ask for crating fee)(Located at 10 Rue Industrielle, Delson, Quebec)
Conveyor with reject station(ID:HP17,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
BELCOR 150 - Semi-automatic top case/box sealer (ID:HP18,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
Oneida Air Systems Mini-Gorilla - 1.5hp Portable dust collector(ID:HP21,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
HUALIAN FxJ-5050ZBR - Hot melt glue case/box sealer(ID:AE78,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
EASTERN CT-121/CH-100 - KAPS-ALL E - Automatic inline capper with caps sorter(ID:UN02,Mandatory Loading Fee: $Ask for crating fee)(Located at 10 Rue Industrielle, Delson, Quebec)
Fortress Technology SC-CONV172SSHD6KICK - Metal detector(ID:AE83,Mandatory Loading Fee: $50)(Located at 10 Rue Industrielle, Delson, Quebec)
ACCRAPLY 35PW - Automatic labeler(ID:AE84,Mandatory Loading Fee: $Ask for crating fee)(Located at 10 Rue Industrielle, Delson, Quebec)
